SPRINT
 This is part of the adjmat module It is only available if you configure PLUMED with ./configure –enable-modules=adjmat . Furthermore, this feature is still being developed so take care when using it and report any problems on the mailing list.

Calculate SPRINT topological variables from an adjacency matrix.

The SPRINT topological variables are calculated from the largest eigenvalue, $$\lambda$$ of an $$n\times n$$ adjacency matrix and its corresponding eigenvector, $$\mathbf{V}$$, using:

$s_i = \sqrt{n} \lambda v_i$

You can use different quantities to measure whether or not two given atoms/molecules are adjacent or not in the adjacency matrix. The simplest measure of adjacency is is whether two atoms/molecules are within some cutoff of each other. Further complexity can be added by insisting that two molecules are adjacent if they are within a certain distance of each other and if they have similar orientations.

Description of components

By default this Action calculates the following quantities. These quanties can be referenced elsewhere in the input by using this Action's label followed by a dot and the name of the quantity required from the list below.

 Quantity Description coord all $$n$$ sprint coordinates are calculated and then stored in increasing order. the smallest sprint coordinate will be labelled label.coord-1, the second smallest will be labelleled label.coord-1 and so on

In addition the following quantities can be calculated by employing the keywords listed below

 Quantity Keyword Description gradient GRADIENT the gradient vmean VMEAN the norm of the mean vector. The output component can be refererred to elsewhere in the input file by using the label.vmean vsum VSUM the norm of sum of vectors. The output component can be refererred to elsewhere in the input file by using the label.vsum spath SPATH the position on the path zpath ZPATH the distance from the path altmin ALT_MIN the minimum value. This is calculated using the formula described in the description of the keyword so as to make it continuous. between BETWEEN the number/fraction of values within a certain range. This is calculated using one of the formula described in the description of the keyword so as to make it continuous. You can calculate this quantity multiple times using different parameters. highest HIGHEST the lowest of the quantitities calculated by this action lessthan LESS_THAN the number of values less than a target value. This is calculated using one of the formula described in the description of the keyword so as to make it continuous. You can calculate this quantity multiple times using different parameters. lowest LOWEST the lowest of the quantitities calculated by this action max MAX the maximum value. This is calculated using the formula described in the description of the keyword so as to make it continuous. mean MEAN the mean value. The output component can be refererred to elsewhere in the input file by using the label.mean min MIN the minimum value. This is calculated using the formula described in the description of the keyword so as to make it continuous. moment MOMENTS the central moments of the distribution of values. The second moment would be referenced elsewhere in the input file using label.moment-2, the third as label.moment-3, etc. morethan MORE_THAN the number of values more than a target value. This is calculated using one of the formula described in the description of the keyword so as to make it continuous. You can calculate this quantity multiple times using different parameters. sum SUM the sum of values
Compulsory keywords
 MATRIX the action that calcualtes the adjacency matrix vessel we would like to analyse
Options
 NOPBC ( default=off ) ignore the periodic boundary conditions when calculating distances SERIAL ( default=off ) do the calculation in serial. Do not parallelize LOWMEM ( default=off ) lower the memory requirements TIMINGS ( default=off ) output information on the timings of the various parts of the calculation
Examples

This example input calculates the 7 SPRINT coordinates for a 7 atom cluster of Lennard-Jones atoms and prints their values to a file. In this input the SPRINT coordinates are calculated in the manner described in ?? so two atoms are adjacent if they are within a cutoff:

DENSITY SPECIES=1-7 LABEL=d1
CONTACT_MATRIX ATOMS=d1 SWITCH={RATIONAL R_0=0.1} LABEL=mat
SPRINT MATRIX=mat LABEL=ss
PRINT ARG=ss.* FILE=colvar


This example input calculates the 14 SPRINT coordinates foa a molecule composed of 7 hydrogen and 7 carbon atoms. Once again two atoms are adjacent if they are within a cutoff:

DENSITY SPECIES=1-7 LABEL=c
DENSITY SPECIES=8-14 LABEL=h

CONTACT_MATRIX ...
ATOMS=c,h
SWITCH11={RATIONAL R_0=2.6 NN=6 MM=12}
SWITCH12={RATIONAL R_0=2.2 NN=6 MM=12}
SWITCH22={RATIONAL R_0=2.2 NN=6 MM=12}
LABEL=mat
... CONTACT_MATRIX

SPRINT MATRIX=mat LABEL=ss

PRINT ARG=ss.* FILE=colvar