LWALLS
This is part of the manyrestraints module
It is only available if you configure PLUMED with ./configure –enable-modules=manyrestraints . Furthermore, this feature is still being developed so take care when using it and report any problems on the mailing list.

Add LOWER_WALLS restraints on all the multicolvar values

This action takes the set of values calculated by the colvar specified by label in the DATA keyword and places a restraint on each quantity, \(x\), with the following functional form:

\( k((x-a+o)/s)^e \)

\(k\) (KAPPA) is an energy constant in internal unit of the code, \(s\) (EPS) a rescaling factor and \(e\) (EXP) the exponent determining the power law. By default: EXP = 2, EPS = 1.0, OFF = 0.

Description of components

By default the value of the calculated quantity can be referenced elsewhere in the input file by using the label of the action. Alternatively this Action can be used to calculate the following quantities by employing the keywords listed below. These quantities can be referenced elsewhere in the input by using this Action's label followed by a dot and the name of the quantity required from the list below.

Quantity Description
bias the instantaneous value of the bias potentials

In addition the following quantities can be calculated by employing the keywords listed below

Quantity Keyword Description
gradient GRADIENT the gradient
vmean VMEAN the norm of the mean vector. The output component can be referred to elsewhere in the input file by using the label.vmean
vsum VSUM the norm of sum of vectors. The output component can be referred to elsewhere in the input file by using the label.vsum
spath SPATH the position on the path
gspath GPATH the position on the path calculated using trigonometry
gzpath GPATH the distance from the path calculated using trigonometry
zpath ZPATH the distance from the path
altmin ALT_MIN the minimum value. This is calculated using the formula described in the description of the keyword so as to make it continuous.
between BETWEEN the number/fraction of values within a certain range. This is calculated using one of the formula described in the description of the keyword so as to make it continuous. You can calculate this quantity multiple times using different parameters.
highest HIGHEST the highest of the quantities calculated by this action
lessthan LESS_THAN the number of values less than a target value. This is calculated using one of the formula described in the description of the keyword so as to make it continuous. You can calculate this quantity multiple times using different parameters.
lowest LOWEST the lowest of the quantities calculated by this action
max MAX the maximum value. This is calculated using the formula described in the description of the keyword so as to make it continuous.
mean MEAN the mean value. The output component can be referred to elsewhere in the input file by using the label.mean
min MIN the minimum value. This is calculated using the formula described in the description of the keyword so as to make it continuous.
moment MOMENTS the central moments of the distribution of values. The second moment would be referenced elsewhere in the input file using label.moment-2, the third as label.moment-3, etc.
morethan MORE_THAN the number of values more than a target value. This is calculated using one of the formula described in the description of the keyword so as to make it continuous. You can calculate this quantity multiple times using different parameters.
sum SUM the sum of values
Compulsory keywords
DATA certain actions in plumed work by calculating a list of variables and summing over them. This particular action can be used to calculate functions of these base variables or prints them to a file. This keyword thus takes the label of one of those such variables as input.
AT the radius of the sphere
KAPPA the force constant for the wall. The k_i in the expression for a wall.
OFFSET ( default=0.0 ) the offset for the start of the wall. The o_i in the expression for a wall.
EXP ( default=2.0 ) the powers for the walls. The e_i in the expression for a wall.
EPS ( default=1.0 ) the values for s_i in the expression for a wall
Options
NUMERICAL_DERIVATIVES ( default=off ) calculate the derivatives for these quantities numerically
SERIAL ( default=off ) do the calculation in serial. Do not use MPI
LOWMEM ( default=off ) lower the memory requirements
TIMINGS

( default=off ) output information on the timings of the various parts of the calculation

Examples

The following set of commands can be used to stop any of the 800 atoms in group A from moving more than 2.46425 nm in the z direction from atom 34137. This is done by adding a lower wall on the z-distance between all the atoms in group A and the position of 34137.

l: ZDISTANCES GROUPA=1-800 GROUPB=34137 NOPBC
LWALLS DATA=l AT=2.46465 KAPPA=150.0 EXP=2 EPS=1 OFFSET=0 LABEL=lwall